High Speed Press HMX Motor Lamination, From 125 - 300 Tons
Press Information
Press Information & Overview
High Speed, High Precision Motor Core Lamination Press
With superior construction and the absence of any accuracy-robbing stroke adjustment mechanisms, the HMX delivers unsurpassed accuracy and die life with the lowest deflection characteristics of any available high-speed press. Thermal cooling control ensures that operating temperatures remain consistent for precise BDC control and accurate part production. And by simply eliminating the unnecessary parts required for stroke adjustment, both maintenance and initial costs are significantly reduced. For increased productivity and profits you only need one adjustment. An AIDA HMX.
Request More InformationPress Features
AIDA HMX High Speed Press Features
- Dynamic Balancing
![Dynamic Balancing]()
- Roll Cam Feed (option)
- Oil Temperature Control / Oil Tank
- Eccentric Shaft
![Eccentric Shaft]()
- Hydraulic Stick Release / Slide Lock System
- 8-Point Slide Guide
![8-Point Slide Guide]()
Bottom Dead Center (BDC) Compensation
Stabilizing Punch Penetration Over TimeSpecially designed suspension points allow for in process BDC adjustment to maintain the desired setting and can be done automatically as often as every 100 press strokes
Combined Bearings
Roller and Oil Film Bearings Housed in a Single UnitControls BDC variations casued by speed change. In high speed presses the bottom dead center position of the slide will change as the press speed goes up or down
Dynamic Balancing
Stabilizes Press Structure by Balancing Inertia Forces in High Speed OperationsInertia forces generated by the slide and upper die can cause the press to become unstable. Balancing of these forces is accomplished by installing a large weight (or weights) that reciprocate exactly opposite the slide and upper die.
Eccentric Shaft Drive
Ideal for Short Stroke Precision Stamping OperationsEccentric shafts are used primarily in high speed and progressive die stamping operations. Allows for placement of bearing supports against both sides of the eccentrics.
Thermal Control
Circulating Temperature Controlled Oil to Every Moving Part of the PressTo control thermal expansion and reduce its effect on your final parts, AIDA stamping presses employ a system that circulates temperature controlled oil (via an external cooling system if necessary) to every moving part in the press and feed.
Press Specifications
HMX High Speed Press Specifications
| 125 Ton | 125 Ton, HMX-M |
| 200 Ton | 200 Ton, HMX-M |
| 300 Ton | 300 Ton, HMX-W |
| 125 - 300 Ton | 125 - 200 Ton, HMX-M |
HMX-1250, 125 Ton High Speed Press Press Specifications
| HMX MODELS | ||
| Press Technical Data | Unit | HMX-1250 |
| Capacity | kN | 1250 |
| U.S. Ton | 140 | |
| Stroke Length | mm | 30 |
| in. | 1.18 | |
| Working energy | J | 1200 |
| in-ton | 5 | |
| Strokes per Minute (No Load) | spm | 200~800 |
| Die Height | mm | 380~430 |
| in. | 14.96~16.93 | |
| Slide Area (LR x FB) | mm | 1300x600 |
| in. | 51.18x23.62 | |
| Bolster Area (LR x FB) | mm | 1300x850 |
| in. | 51.18x33.46 | |
| Max upper die weight | kg | 500 |
| lbs. | 1102 | |
| Side opening | mm | 350 x Die Height |
| in. | 13.78 x Die Height | |
HMX-1250M, 125 Ton High Speed Press Press Specifications
| HMX-M MODELS | ||
| Press Technical Data | Unit | HMX-1250M |
| Capacity | kN | 1250 |
| U.S. Ton | 140 | |
| Stroke Length | mm | 30 * |
| in. | 1.18 * | |
| Working Energy | J | 1200 |
| in-ton | 5 | |
| Strokes per Minute (No Load) | spm | 160~500 |
| Die Height | mm | 380~430 |
| in. | 14.96~16.93 | |
| Slide Area (LR x FB) | mm | 1300x600 |
| in. | 51.18~23.62 | |
| Bolster Area (LR x FB) | mm | 1300x850 |
| in. | 51.18~33.46 | |
| Max upper die weight | kg | 500 |
| lbs. | 1102.31 | |
| Side opening | mm | 450 x Die Height |
| in. | 17.72 x Die Height | |
| * Stroke lengths less than 30 mm can also be accommodated. | ||
HMX-2000, 200 Ton High Speed Press Press Specifications
| HMX MODELS | ||
| Press Technical Data | Unit | HMX-2000 |
| Capacity | kN | 2000 |
| U.S. Ton | 220 | |
| Stroke Length | mm | 30 |
| in. | 1.18 | |
| Working energy | J | 2000 |
| in-ton | 9 | |
| Strokes per Minute (No Load) | spm | 200~600 |
| Die Height | mm | 400~480 |
| in. | 15.75~18.9 | |
| Slide Area (LR x FB) | mm | 1700x650 |
| in. | 66.93x25.59 | |
| Bolster Area (LR x FB) | mm | 1700x950 |
| in. | 66.93x37.4 | |
| Max upper die weight | kg | 900 |
| lbs. | 1984 | |
| Side opening | mm | 460 x Die Height |
| in. | 18.11 x Die Height | |
HMX-2000M, 200 Ton High Speed Press Press Specifications
| HMX-M MODELS | ||
| Press Technical Data | Unit | HMX-2000M |
| Capacity | kN | 2000 |
| U.S. Ton | 220 | |
| Stroke Length | mm | 30 * |
| in. | 1.18 * | |
| Working Energy | J | 2000 |
| in-ton | 9 | |
| Strokes per Minute (No Load) | spm | 160~450 |
| Die Height | mm | 400~480 |
| in. | 15.75~18.9 | |
| Slide Area (LR x FB) | mm | 1700x650 |
| in. | 66.93~25.59 | |
| Bolster Area (LR x FB) | mm | 1700x950 |
| in. | 66.93~37.4 | |
| Max upper die weight | kg | 900 |
| lbs. | 1984.158 | |
| Side opening | mm | 530 x Die Height |
| in. | 20.87 x Die Height | |
| * Stroke lengths less than 30 mm can also be accommodated. | ||
HMX-3000, 300 Ton High Speed Press Press Specifications
| HMX MODELS | ||
| Press Technical Data | Unit | HMX-3000 |
| Capacity | kN | 3000 |
| U.S. Ton | 340 | |
| Stroke Length | mm | 30 |
| in. | 1.18 | |
| Working energy | J | 3000 |
| in-ton | 13 | |
| Strokes per Minute (No Load) | spm | 160~500 |
| Die Height | mm | 420~520 |
| in. | 16.54~20.47 | |
| Slide Area (LR x FB) | mm | 2000x750 |
| in. | 78.74x29.53 | |
| Bolster Area (LR x FB) | mm | 2000x1000 |
| in. | 78.74x39.37 | |
| Max upper die weight | kg | 1300 |
| lbs. | 2866 | |
| Side opening | mm | 560 x Die Height |
| in. | 22.05 x Die Height | |
HMX-3000W, 300 Ton High Speed Press Press Specifications
| HMX MODELS | ||
| Press Technical Data | Unit | HMX-3000W |
| Capacity | kN | 3000 |
| U.S. Ton | 340 | |
| Stroke Length | mm | 30 |
| in. | 1.18 | |
| Working energy | J | 3000 |
| in-ton | 13 | |
| Strokes per Minute (No Load) | spm | 120~410 |
| Die Height | mm | 420~520 |
| in. | 16.54~20.47 | |
| Slide Area (LR x FB) | mm | 2260(2300)x1000 * |
| in. | 88.98(90.55)x39.37 * | |
| Bolster Area (LR x FB) | mm | 2300x1200 |
| in. | 90.55x47.24 | |
| Max upper die weight | kg | 1500 |
| lbs. | 3307 | |
| Side opening | mm | 560 x Die Height |
| in. | 22.05 x Die Height | |
| * The value in ( ) indicates the area for tool change. | ||
HMX, 125 - 300 Ton High Speed Press Specifications
| HMX MODELS | |||||
| Press Technical Data | Unit | HMX-1250 | HMX-2000 | HMX-3000 | HMX-3000W |
| Capacity | kN | 1250 | 2000 | 3000 | 3000 |
| U.S. Ton | 140 | 220 | 340 | 340 | |
| Stroke Length | mm | 30 | 30 | 30 | 30 |
| in. | 1.18 | 1.18 | 1.18 | 1.18 | |
| Working energy | J | 1200 | 2000 | 3000 | 3000 |
| in-ton | 5 | 9 | 13 | 13 | |
| Strokes per Minute (No Load) | spm | 200~800 | 200~600 | 160~500 | 120~410 |
| Die Height | mm | 380~430 | 400~480 | 420~520 | 420~520 |
| in. | 14.96~16.93 | 15.75~18.9 | 16.54~20.47 | 16.54~20.47 | |
| Slide Area (LR x FB) | mm | 1300x600 | 1700x650 | 2000x750 | 2260(2300)x1000 * |
| in. | 51.18x23.62 | 66.93x25.59 | 78.74x29.53 | 88.98(90.55)x39.37 * | |
| Bolster Area (LR x FB) | mm | 1300x850 | 1700x950 | 2000x1000 | 2300x1200 |
| in. | 51.18x33.46 | 66.93x37.4 | 78.74x39.37 | 90.55x47.24 | |
| Max upper die weight | kg | 500 | 900 | 1300 | 1500 |
| lbs. | 1102 | 1984 | 2866 | 3307 | |
| Side opening | mm | 350 x Die Height | 460 x Die Height | 560 x Die Height | 560 x Die Height |
| in. | 13.78 x Die Height | 18.11 x Die Height | 22.05 x Die Height | 22.05 x Die Height | |
| * The value in ( ) indicates the area for tool change. | |||||
HMX-M, 125 - 200 Ton High Speed Press Specifications
| HMX-M MODELS | |||
| Press Technical Data | Unit | HMX-1250M | HMX-2000M |
| Capacity | kN | 1250 | 2000 |
| U.S. Ton | 140 | 220 | |
| Stroke Length | mm | 30 * | 30 * |
| in. | 1.18 * | 1.18 * | |
| Working Energy | J | 1200 | 2000 |
| in-ton | 5 | 9 | |
| Strokes per Minute (No Load) | spm | 160~500 | 160~450 |
| Die Height | mm | 380~430 | 400~480 |
| in. | 14.96~16.93 | 15.75~18.9 | |
| Slide Area (LR x FB) | mm | 1300x600 | 1700x650 |
| in. | 51.18~23.62 | 66.93~25.59 | |
| Bolster Area (LR x FB) | mm | 1300x850 | 1700x950 |
| in. | 51.18~33.46 | 66.93~37.4 | |
| Max upper die weight | kg | 500 | 900 |
| lbs. | 1102.31 | 1984.158 | |
| Side opening | mm | 450 x Die Height | 530 x Die Height |
| in. | 17.72 x Die Height | 20.87 x Die Height | |
| * Stroke lengths less than 30 mm can also be accommodated. | |||
Technical Resources
Frequently Asked Questions
Answers to Your Questions about AIDA and Press Related Topics We offer answers for all types of common questions - whether technical in nature or as simple as where to look for career opportunities. Examples of some questions are: What is HOLP? Where is the closest AIDA facility located? How can we get a copy of the manual for our AIDA press? What is reverse tonnage? Visit our frequently answered questions section to find answers to your questions.
View Frequently Asked QuestionsAIDA-Tech White Papers
Technical Topics & Information Topics such as connections spacing, slide guiding systems, reverse tonnage and more, AIDA-Tech White papers offer information for a variety of technical subjects related to stamping presses and press operations.
View AIDA-Tech White PapersMetalforming Articles
Articles from Industry Publications We maintain a library of metalforming articles from a variety of industry publications covering a wide range of topics centered on stamping and press operations. Topics include press technology, market trends, and press applications. Many of the articles collected here have been authored by or contributed to by AIDA associates.
View Metalforming ArticlesAIDA Press User Testimonials
Case Studies from Stampers AIDA press users describe their companies and business operations, as well as, how they have used AIDA technology to achieve their production goals and expand their capacity and capabilities. Examples are provided from many different types of companies from job shops, to tier suppliers, to OEMs. Read on to see how leaders in many industries have successfully partnered with AIDA.
View User TestimonialsApplications Studies & Die Trials
Schedule an Application Review or Die Trial, Today Application studies and die trials provided by AIDA prove, with your own dies and part drawings, how AIDA stamping press technology can have multiple benefits to your manufacturing operations, including increased production rates, higher quality parts, reduced scrap, and reduced maintenance.
Applications Studies & Die TrialsStamping Press Technology
Industry Leading Forming Systems For over 100 years AIDA has been developing and manufacturing specialized metalforming products like metal stamping presses and related automation equipment, such as transfers, robots, and feeders. AIDA's exclusive stamping press technology is used throughout our wide range of presses, from 30 through 4,000 tons capacity.
Stamping Press TechnologyEducational Partners & Resources
Research and Development Not only does AIDA invest 5% of annual revenue towards internal research and development, but AIDA also actively seeks and participates in research with educational institutions such as the Center for Precision Forming (OSU), Institut für Umformtechnik, Edison Welding and others.
More About Educational PartnersTerms & Glossary
Operations, Components, & Press Industry Terminology A variety of functions may be performed by many different types of presses, depending upon the tooling. Typical press operations and other terms referring to press features and functions, as well as basic press characteristics and designs are explained in this section of our website.
View Terms & Glossary